ASKERN Plumbing & Heating
The Askern Plumbing and Heating van

Heating & Gas

Central heating installation in Doncaster

Central heating installation in Doncaster is a bigger job than a boiler swap: the boiler, every radiator, the pipes between them and the controls are all chosen together. Mick Worthington, our Gas Safe registered engineer, surveys the house room by room at no charge, and you have the price in writing before anything is booked.

Who needs a full central heating installation?

Most heating jobs are a new boiler on pipes and radiators that stay. A full installation is for the houses where that is not enough, and it tends to be one of three:

  • A house that has never had it. Gas fires, storage heaters or plug-in heaters, and no radiators at all.
  • A system past saving. Old pipes, radiators that never get warm and a boiler on its last legs, where patching one part only moves the fault to the next.
  • A house that has changed. An extension, a loft room or a refit that the old system was never sized for.

If yours is none of these and it is only the boiler that has had its day, our page on new boilers is the one you want.

What goes into a gas central heating system

  • The boiler Sized to the house, not picked off a shelf.
  • A radiator or towel rail in each room you want heated Each one sized for its own room.
  • Flow and return pipework Hot water out to the radiators and cooler water back to the boiler.
  • Controls A timer, a room thermostat and a valve on the radiators.
  • A hot water cylinder, with some boilers A combi boiler does without one.
  • The gas supply to the boiler Checked to see it is big enough for the new boiler.

How do you work out the size of the radiators?

By measuring, not by eye. Every room loses heat at its own rate, depending on its size, its outside walls, its windows and what is above and below it. The Building Regulations guidance for England, Approved Document L, says a heating system should be based on "an appropriate heat loss calculation for the dwelling", and that systems "should not be significantly oversized".

That calculation gives a figure for each room, and the radiator is chosen to match it. Guess low and the room never warms up. Guess high and you have paid for metal you did not need.

Why new radiators often look bigger than the old ones

The same guidance says a newly installed system should be sized to heat the house with the water leaving the boiler at 55°C or lower. Older systems were designed around much hotter water. Cooler water gives off less heat from the same radiator, so the radiator has to be larger to do the same job.

The gain is in the running. A modern boiler is at its most efficient when the water coming back to it is cool, and a system built for lower temperatures lets it work that way. Where a room has no space for a bigger radiator, the guidance allows for that: the system is designed to the lowest temperature that will still heat the house.

What controls does a new heating system need?

Enough that each room can be set on its own. The guidance asks for thermostatic control in each room, and the usual way to provide it is a thermostat in one room and a thermostatic radiator valve, a TRV, on the radiators everywhere else. A TRV is the numbered dial on the end of a radiator. It senses the room and closes the radiator down once the room is warm enough.

They earn their place. BEAMA, the trade association whose members make heating controls, cites tests at the University of Salford in which a typical gas boiler used around 18% less energy over a heating season with TRVs fitted.

Mick also fits smart thermostats, and a new system is the easiest time to add one, because the wiring and the controls are already being done.

How a central heating installation runs

  1. A survey, room by room

    Mick looks at every room that needs heat, where a boiler and its flue could go, where pipes can run and what the gas supply is like. It is free.

  2. A written price

    You get a figure and a list of what it covers. Nothing is booked until you say so.

  3. Pipes and radiators

    The pipework goes in first, under floors where it can, then the radiators are hung and connected.

  4. Boiler and controls

    The boiler is fitted and connected to the gas, the flue, the pipework and the controls.

  5. Filled, tested and set up

    The system is filled, checked for leaks, run up to temperature and adjusted so every radiator gets its share of the heat.

  6. Shown to you

    You are shown how the timer, the thermostat and the radiator valves work before Mick leaves.

Radiators come in more than one shape

  • A tall column radiator fitted on a bathroom wall above black tiling
    A tall column radiator in one of the bathrooms we fitted.
  • A matt black towel rail on a grey tiled wall
    A matt black towel rail, from the wet room in our gallery.

What if the house is not on mains gas?

Then the same kind of system can run on LPG, which is gas delivered to a tank or bottles outside the house. Mick installs LPG central heating as well as mains gas, and services and repairs it afterwards. The radiators, pipes and controls are the same. What changes is the boiler and where the gas comes from, so the survey also looks at where a tank or bottles could stand.

How much does central heating installation cost in Doncaster?

More than a boiler on its own, and by how much depends on the house, which is why you will not get a number from us over the phone. The things that move it:

  • How many rooms need a radiator, and how big each has to be.
  • Which type of boiler suits the house, and whether it needs a cylinder.
  • How easily pipes can be run. Timber floors lift. Solid floors and finished rooms take longer.
  • Whether the gas supply needs upgrading to feed the boiler.
  • Whether it is mains gas or LPG.

Mick comes out, looks, and puts the price in writing. The survey costs nothing.

What customers say about Mick

Our Checkatrade score is 10 out of 10 across 350 reviews, we have been members since 2016, and membership means the work is guaranteed up to £1,000. Two customers, in their own words:

Arrived exactly at the time stated. The job, which should have been straightforward, wasn't, and Mick sorted it without any stress.

Sophie M, Checkatrade, DN8

Fast and reliable service from Mick and his son. Very responsive to phone calls, tidy worker. Reasonably priced.

Beverley Mcdonough, Google review

Book the survey

The number is 07734 694 463 and Mick answers Monday to Friday, 8am to 5pm. Have a rough count of the rooms ready, and what heats the house now. If you would rather type, the same number takes WhatsApp.

Once a system is in, a yearly boiler service is what most boiler makers ask for under their warranty. If the heating you already have has stopped, go to boiler repair instead. The full list of Mick's gas work is under heating and gas.

Central heating questions

Will the floors have to come up?

Some of them, usually. Upstairs, pipes normally run under the floorboards, so boards are lifted and put back. Downstairs depends on the floor: a timber floor can be lifted the same way, while with a solid floor the pipes more often drop down from the ceiling and are boxed in or run along the skirting. You will know which rooms are affected from the survey.

Can you add radiators to the heating I already have?

Often, yes. An extra radiator for an extension or a cold room is a much smaller job than a new system. What has to be checked first is whether the boiler has the capacity to spare and whether the existing pipes can carry the extra, and that takes a look.

Why is there no thermostatic valve on the radiator in the hall?

Because that is usually where the room thermostat is. Approved Document L says thermostatic radiator valves should not be used in the same room as the thermostat. With both in one room, the valve can shut the radiator before the thermostat is satisfied, and the boiler keeps running for a room that will never get there.

Do the heating pipes need insulating?

Where they leave the heated part of the house, yes. For a new system, Approved Document L says heating pipes should be insulated where they pass outside the heated living space, including through voids. In practice that means runs through a garage, a loft or under a suspended ground floor.

What paperwork should I get with a new heating system?

Operating and maintenance instructions for what has been fitted. Approved Document L says these should be given to the owner, with enough in them to run the system efficiently. For a complete new system it also says the energy performance of the whole system should be assessed and the record handed over with the manufacturer's literature. Keep it all with the boiler's warranty.

Askern, Doncaster

Ring Mick.

Tell him what has gone wrong, or what you want doing. He will tell you what it takes and what it costs, and if he cannot help he will say so.

Mon to Fri, 8am to 5pm

10 out of 10 from 350 Checkatrade reviews. Gas Safe registered.

The Askern Plumbing and Heating van, carrying the Gas Safe and Checkatrade logos

Can’t talk right now?

Leave your number and we will ring you back.

We only use this to ring you back about the job.

Call Mick, 07734 694 463